Difference between revisions of "AppleII"

Latest revision as of 01:48, 6 January 2011

Showcase Setup

Apple II Plus (Kuen Hwa clone) with following cards:
- slot 0: 16KB RAM expansion "language card"
- slot 3: 80 columns display card
- slot 4: Z80 "soft card" for running CP/M (t.b.t)
- slot 6: Disk II interface card
Sony PVM-90CE monochrome monitor
Dual floppy drive.

Other Pieces

ITT 2020: an Apple II europlus clone:
- Power supply seems broken, doesn't give good voltages, now removed.
- Untested
ZD ucom: another Apple II clone with a numeric keypad
- Power supply is removed
- Untested
Expansion cards:
- D780C (Z80 clone)
- Disk II + Shugart
- Unidentified, has a 26 pin flat cable connector and only an EEPROM and 74LS ICs.
- Unidentified, TV modulator ?

Origin

The Kuen Hwa clone, some cards, the Sony monitor and a full height disk drive was donated by the University of Antwerp around 1993. The monitor is rumoured to have been their first computer display. The other computers, the dual diskdrive and some cards where purchased later in the 1990's to replace the broken disk drive.

Condition

The showcase setup is in working condition, although:
- The computer has it's logo badge is missing.
- The monitor starts to make an awful noise when it gets hot.
- The disk drives don't seem to be very reliable

Software

I'm able to run following software:

Apple DOS 3.3 with various programs:
- Visicalc
- Games: Castle Wolfenstein
Prodos 8 v1.9 with ADTpro
CP/M with various programs:
- DBase
- COBOL-80
- Turbo Pascal
- GBASIC

Data Exchange

Using ADTPro over the audio/cassette port allows to transfer disk images (.DSK) to and from physical 5 1/4" floppies.

Tons of images can be found here

It takes about 20 minutes for a 180KB disk side, requires trial-and-error adjusting of mic and headphone volume on the PC side and good audio cables. Once it's set up it is fairly reliable.

Also of interest: manipulate prodos disk images with AppleII::ProDOS

Usage Hints

Upon power-on the Kuen Wha simply shows COMPUTER on the top of the screen and infinitely tries to boot from disk. You can escape to BASIC by pressing RESET.

The ITT starts in monitor.

Monitor

You are in the built-in system monitor if you see the star prompt:

Press ctrl-B return to switch to BASIC

Applesoft BASIC

The apple II Plus has Applesoft BASIC in ROM. A.k.a floating point BASIC, as opposed to the integer basic of the original apple II.

You are in Applesoft BASIC if you see the bracket prompt:

Boot a floppy:

 PR#6

Switch to 80 columns:

 PR#3

Go into the monitor:

 CALL -151

DOS 3.3

For this you need to boot any DOS 3.3 formatted disk. All disks contain the OS. The OS just adds some extra commands to BASIC:

CATALOG
RUN <program>

ProDOS 8

For this you need to boot a ProDOS system boot disk (not all ProDOS disks contain the OS). Usually a ProDOS disk boots a menu and you can quit to BASIC.

The OS adds some extra commands to BASIC:

CAT 
RUN <program>

CP/M

Make sure you have the Z80 card installed and you connect your screen to 80 columns or you don't see anything happening.

Survival commands:

CAT
<program_name_without.COM> 
B:

Done

Restoration of the ITT 2020

Connected a PC power supply. Reseated the CPU and ROMs. Now it starts up in monitor. CTRL-B brings you to Applesoft BASIC.

Connected the known good disk drives in slot 6 and tried to boot any disk (dos, prodos) by doing PR#6 starts loading but then halts with an error:

** RELOCATION / CONFIGURATION ERROR **

Wrote a memory test program in BASIC. This pinpointed that bit 1 of address $5105 and bit 4 of $9000 were stuck on. Translating this to the motherboard layout I knew exactly which RAM chips to replace. I stole them from the ZDucom, they are regular 4116's. Problem solved!

It now boots Prodos etc. But games (using high res graphics) show vertical stripes. I tried replacing the 74LS194 at B4 but it didn't help. I'm guessing that it is actually an incompatibility of the 2020, that it has an 9'th bit in the first 16K that is displayed in highres mode. Using HGR> and plotting in BASIC works fine, but the binary loaded image obviously only fills 8 bits, the 9th bit being random yielding the vertical bars.

@@ Line 5: / Line 5: @@
 == Showcase Setup ==
-* Apple II Plus (probable Kuen Hwa clone) with following cards:
+* Apple II Plus (Kuen Hwa clone) with following cards:
 ** slot 0: 16KB RAM expansion "language card"
 ** slot 3: 80 columns display card
@@ Line 39: / Line 39: @@
 == Software ==
+I'm able to run following software:
 * Apple DOS 3.3 with various programs:
@@ Line 44: / Line 46: @@
 ** Games: Castle Wolfenstein
 * Prodos 8 v1.9 with ADTpro
-* CP/M with various programs (t.b.t)
+* CP/M with various programs:
+** DBase
+** COBOL-80
+** Turbo Pascal
+** GBASIC
 == Data Exchange ==
+[[File:P1010851.resized.JPG|thumb|]]
 Using [http://adtpro.sourceforge.net/ ADTPro] over the audio/cassette port allows to transfer disk images (.DSK) to and from physical 5 1/4" floppies.
+Tons of images can be found [ftp://ftp.apple.asimov.net/pub/apple_II/images/ here]
 It takes about 20 minutes for a 180KB disk side, requires trial-and-error adjusting of mic and headphone volume on the PC side and good audio cables. Once it's set up it is fairly reliable.
@@ Line 56: / Line 66: @@
 == Usage Hints ==
-Upon power-on the computer simply shows "COMPUTER" on the top of the screen and infinitely tries to boot from disk.
+Upon power-on the Kuen Wha simply shows <tt>COMPUTER</tt> on the top of the screen and infinitely tries to boot from disk.  You can escape to BASIC by pressing RESET.
+The ITT starts in monitor.
+=== Monitor ===
+You are in the built-in system monitor if you see the star prompt:
+ *
-Pressing reset brings you in Applesoft BASIC (from ROM). From there you can get in the monitor by typing CALL -151
+Press ctrl-B return to switch to BASIC
-To use disks you must boot an OS like:
+=== Applesoft BASIC ===
-* DOS 3.3
-* ProDOS 8
-* CP/M
-To boot from BASIC without power cycle:
+The apple II Plus has Applesoft BASIC in ROM. A.k.a floating point BASIC, as opposed to the integer basic of the original apple II.
+You are in Applesoft BASIC if you see the bracket prompt:
+ ]
+Boot a floppy:
    PR#6
-To switch to 80 columns:
+Switch to 80 columns:
    PR#3
+Go into the monitor:
+  CALL -151
+=== DOS 3.3 ===
+For this you need to boot any DOS 3.3 formatted disk. All disks contain the OS.  The OS just adds some extra commands to BASIC:
+ CATALOG
+ RUN <program>
+=== ProDOS 8 ===
+For this you need to boot a ProDOS system boot disk (not all ProDOS disks contain the OS). Usually a ProDOS disk boots a menu and you can quit to BASIC.
+The OS adds some extra commands to BASIC:
+ CAT
+ RUN <program>
+=== CP/M ===
+[[File:P1010856b.JPG|thumb|]]
+Make sure you have the Z80 card installed and you connect your screen to 80 columns or you don't see anything happening.
+Survival commands:
+ CAT
+ <program_name_without.COM>
+ B:
 == Done ==
@@ Line 82: / Line 130: @@
   ** RELOCATION / CONFIGURATION ERROR **
-Tried with and without the language card in slot 0.
+Wrote a memory test program in BASIC. This pinpointed that bit 1 of address $5105 and bit 4 of $9000 were stuck on. Translating this to the motherboard layout I knew exactly which RAM chips to replace.  I stole them from the ZDucom, they are regular 4116's. Problem solved!
-== To Do ==
-Try CP/M.
+It now boots Prodos etc. But games (using high res graphics) show vertical stripes. I tried replacing the 74LS194 at B4 but it didn't help.  I'm guessing that it is actually an incompatibility of the 2020, that it has an 9'th bit in the first 16K that is displayed in highres mode. Using <tt>HGR</tt>> and plotting in BASIC works fine, but the binary loaded image obviously only fills 8 bits, the 9th bit being random yielding the vertical bars.

Difference between revisions of "AppleII"

Latest revision as of 01:48, 6 January 2011

Contents